Nov 04, 2012 · Linksys WRT54G, ssh, "no route to host" marnold: Linux - Networking: 1: 09-29-2010 12:33 PM: Handling a "No route to host" message in a script: kaujot: Programming: 2: 03-27-2008 06:14 PM: shorewall routing issue: "no route to host" from dmz: spargonaut: Linux - Networking: 0: 06-07-2007 10:09 AM: a/p connected, route correct, ping router
Apr 09, 2017 · telnet: connect to address 174.11.1.11: No route to host telnet: Unable to connect to remote host: No route to host Reason: When i diagnosed then i found that internal firewall was enabled on the machine 174.11.1.11 thats why i was not able to telnet the required ports. ssh: connect to host sample.com port 12345: No route to host TL;DR（概要） SSH で接続する際に指定したポートが、 サーバー側の SSH ポートと合っていない 場合に No route to host エラーが発生します。 May 19, 2018 · Using the pcs stonith describe fence_ilo4_ssh command you can view all configurable options for the fence_ilo4_ssh resource. pcs stonith describe fence_ilo4_ssh. Example Output. fence_ilo4_ssh - Fence agent for HP iLO over SSH fence_ilo_ssh is a fence agent that connects to iLO device. It logs into device via ssh and reboot a specified outlet. I am trying to ssh to a site where I have an account but recently I am receiving the following messages on both openSUSE11 and 11.1 ken@linux:~> ssh cell-user.cc.gt.atl.ga.us -l username ssh: connect to host cell-user.cc.gt.atl.ga.us port 22: No route to host I have checked that SSH is enabled on the firewall and I checked during installation as well.
「ssh: connect to host 55555 port 22: No route to host」 というエラーが返ってきます。 しかしMacからRaspberry Piにsshでログインすることはできます。 ssh user@ 192.168.1.100-p 55555. これで普通にパスワードを聞かれてログインできます。
Nov 04, 2012 · Linksys WRT54G, ssh, "no route to host" marnold: Linux - Networking: 1: 09-29-2010 12:33 PM: Handling a "No route to host" message in a script: kaujot: Programming: 2: 03-27-2008 06:14 PM: shorewall routing issue: "no route to host" from dmz: spargonaut: Linux - Networking: 0: 06-07-2007 10:09 AM: a/p connected, route correct, ping router IMO, the easiest way to enable SSH, is to add a file, SSH (no extension) into the boot partition (also accessible via most Windows machines). Just to be safe and not waste my time, I also add a file called ssh.txt there. You'll need network connectivity. May 05, 2006 · vbharadwaj@deepblue:~$ ssh deepblue-1-8 ssh: connect to host deepblue-1-8 port 22: No route to host. I looked up the iptables command and this was my output vbharadwaj@deepblue:~$ sudo /sbin/iptables -L -n [sudo] password for vbharadwaj: Chain INPUT (policy ACCEPT) target prot opt source destination. Chain FORWARD (policy ACCEPT) No route to host means the server doesnt know how to route the packet (routing table, however I have never seen it only occur on one protocol and not another). In my case. No NAT Internet connection. No IPTABLES Ping works I can connect to ip's either side of the broken ip. The broken ip says "no route to host" on any tcp port.
ssh user@75.xxx.xxx.xx ssh: connect to host 75.xx.xxx.xxx port 22: No route to host rsync works on both machines solong it is an internal transfer of data. I can connect to both servers via ssh from my desktop computer without a problem at all, but the two servers hate each other and they wont connect togather.
May 19, 2018 · Using the pcs stonith describe fence_ilo4_ssh command you can view all configurable options for the fence_ilo4_ssh resource. pcs stonith describe fence_ilo4_ssh. Example Output. fence_ilo4_ssh - Fence agent for HP iLO over SSH fence_ilo_ssh is a fence agent that connects to iLO device. It logs into device via ssh and reboot a specified outlet. I am trying to ssh to a site where I have an account but recently I am receiving the following messages on both openSUSE11 and 11.1 ken@linux:~> ssh cell-user.cc.gt.atl.ga.us -l username ssh: connect to host cell-user.cc.gt.atl.ga.us port 22: No route to host I have checked that SSH is enabled on the firewall and I checked during installation as well.